Відео

LOL I went through 3 cheap flare tools thinking they were junk I left that little copper tubing in there.

yap

I found a new set on the roof connected to a system

I ordered a replacement capacitor for a unit very similar to this but the one spec'd is too big: 2" vs 1.75 in. diameter and won't fit in the slot for it. Where should I mount it now as supposedly it's the only one recommended by the manufacturer?

This has been discontinued?

Where did you get the 1amp version. Amazon is selling $63.99 and it said 1.3amp. I was going to order one us motor same everything but it rated 1.6 amp so cancelled.

What's best way to remove the bottom drain (base) pan as my capacitor leaked oil and I need to clean the water wheel and surrounding area etc. under the condenser coils?

Did anyone have any issues with this motor?

Mines is about 2 yrs old and I may have used it about 75 times .. sensor bad and they said I need to replace the filter regularly .. Replace filter just after about 75 uses !!!

Hey man, good video. Have you ever seen one of this kind of unit that leaks a ton but has a little to no water in the catch pan? We have a Whynter ARC-14s and a day ago it started leaking a bunch of water. Went to put a hose on the pan but nothing came out. Tilted the unit to see if anything was in there and only got a few ounces. Yet it's producing a bunch of water, to the point we may have to get the carpet replaced. It's of course july in northern VA atm so it's 100F with almost 100% humidity most days and we can't go without running it. Not sure I could afford a tech at this point and I simply can not find a service manual for these things. Any advice would be helpful man.

This video really helps a lot :)👍

The only thing not safe with that unit . Is you working on it 😂..

Old skool . I got this lol

Good walk thru next level stuff here 👌

Big pic diagnosees ovaheeyah yessur 👍👍💦💦

I’m recommending they call surf bros. They will get it running

I have to comment on this one. Quite a few of the other houses in my neighborhood still have these units on them. The evap coil is directly behind where the drain connection is and you have to pull the top to clean it.and lastly, i believe DNP stands for Day, Night, Payne

Affording the payments is way different than affording the truck

That wasn't even the Denali lol, Denali is 95k before the fees, 110k+ for an Ultimate

Hey Jon- Rookie question- What about the air thats in the yellow Charge/Vacuum line? So like if I only hooked up to check system pressures without hooking up the yellow cha/vac line, How do I ensure that i wont be sucking air from the yellow line into the system along with the refrigerant when returning refrigerant back into the system? I understand purging the yellow line if connected to a tank, but can't seem to find any info on how to clear it of air on a system check if you don't use it.. Many THX !!

Get a Tundra

Pocket change 😂

I picked one of these today I’m going to put it through a some real scenarios 😅🤷🏻‍♂️

Tightness test is a mbar pressure test for gas pipework 👍 In the UK, we let gas into the pipework from the shut off valve to around half the working pressure then close the valve and watch for a pressure rise. This called a let-by test to test valve integrity. We then charge the pipe to working pressure (21mbar) and close the shut off valve. We time 2 minutes and watch for a pressure drop. This checks the “tightness” of the pipework. You can do it manually (manometer & watch/timer) or with a Testo setup to record it etc 👍

I am glad that I found this! I am a “Run-Test Operator” for an HVAC company. I test the newly assembled units. The test stands have old, worn hoses. I have asked for new ones many times and got nowhere. I purchased 8 Yellow Jacket Plus II hoses with the ball valves at $60 each. Long story short, despite using Coremax Snapmates on every hose, some of the gaskets are wearing. I was worried that I was going to have to buy new hoses.

Harbor freight is notorious to charge you restock feees. It’s a rip off

I picked this up and used it a few times. Works good on mini splits, i havent tested it on anything big yet

Looks interesting

Good job. I had my exhaust fan blower cage break just like yours. Dozens of the slat pieces on the floor of the portable A/C. I cleaned that up, and can spin the squirrel cage easily by hand. But when I turn on the system, cold air blows out the top, but no hot air discharges out the back. The exhaust fan motor does not appear to be kicking on. So ... Do you think when the cage breaks, the motor typically fails, too? What voltage should I get at the exhaust motor? Thanks.

Heck yeah, proper De Minimus, watched this other guy on UA-cam and was like, way too much release as he didn’t use this technique! 🎉

I can't believe how quiet this is compared to the new ones. It's even more quiet over my 2007 Whirlpool direct drive.

Good video. Thanks. Viewers should know the compressor being tested is a "scroll" type made by Copeland, which, according to Copeland, can show low ohms on the Supco and still be perfectly functional.

I'm not getting all of this info on my screen at all.

Drilled rotors must have some serious horsepower under the hood 🤨🤔🙆🏻‍♂️

Thank you Jonny Sunset for keeping us up on new tools and hvac tricks

Manufacturer's Demo Video: ua-cam.com/video/UqPxjH-hWIA/v-deo.htmlsi=6Kzf8-3IdHWkCVdI

I've used it. It's hard to control heat because it's different than brazing but it works great

Thank Goodness, for GOODMAN!

You and the choir boys popped in my head today when I had to pay $225 to have the capacitor replaced in my AC unit...lol LongTime

I would buy a used car from this man .

send Joe and Ted a case or at least give him their information.

We here at Comfort Medic support and approve this product!

Sounds very promising.

Ain't buying it

People need to understand they have been sold a bunch of crap in the U.S - China has been improving their products exponentially fast to the point where there are now many decent products from China for a fraction of the cost of the highway robbery “brands”. I bought a Chinese chainsaw for $189.00 and cut down big trees for two years without one problem - for the average person, you would be a fool not to buy the Chinese versions today. It’s not 20 years ago, China is improving every day - for a fraction of the price. You want lower American Prices? Don’t buy American -all you get is robbed by the corporate thieves. We have been sold a bunch of crap to keep corporate America fat, they aren’t helping us - they are burying us. I’m done flag waving, they’ve done $hit - Now I buy Chinese.